If a name containing more than 32 characters is applied as part of the changes, it will be ignored. To edit the beacon name, start by tapping on the beacon name edit box under the “Beacon Name” label.The beacon name can be set to a maximum length of 32 characters. The Beacon Detail screen contains fields for configuring the beacon parameters, and fields that display beacon status information. Note: If the Beacon list remains empty after 15 seconds of scanning, we can assume there are no RadBeacon E devices in range. Next, you should see a progress icon with a message indicating that scanning has started, as shown below.Īfter a few seconds of scanning, the home screen should list the available in-range devices. The device scanning process is initiated by pulling down on the home screen of the RadBeacon E App. The RadBeacon E App allows users to configure their RadBeacon E4 device parameters. Only while in configuration-mode the beacon will broadcast connectable advertisements. The beacon will remain in configuration-mode for the next 10 minutes. The blue LED will blink twice to confirm beacon has entered configuration-mode. Configuration-mode is entered after pressing and releasing the button while not in configuration-mode. The button on the side of the beacon is used for enabling configuration-mode. Refer to the slot configuration section below for details on how to enable/disable a slot. The E4 can be switched off by disabling all the 5-slots on the beacon using the RadBeacon E app. The RadBeacon E4 allows for user configuration via the RadBeacon E App available for iOS and Android devices. The RadBeacon E4 is powered from 4 user-replaceable AA batteries. The RadBeacon E4 can be configured to advertise data in up to 5 individual slots. The RadBeacon E4 supports the 4 most popular beacon protocols iBeacon, AltBeacon, Eddystone UID, and Eddystone URL. In order to re-enter normal operational model, simply remove and replace power to the device.The RadBeacon E4 is the next generation Radius Networks Bluetooth™ Smart proximity multi-beacon device. Reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. Press the Action Menu button and select DFU. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Press the Action Menu button and select Lock. Submit a valid PIN to reset the settings for your beacon to factory defaults. Reset the device to the original factory settings. Press the Action Menu button and select Reset. Submit a new and existing PIN to update the PIN for your beacon. Press the Action Menu button and select Update PIN. Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Press the Action Menu button and select Range. Update the measured power value with the results of your calibration activity and update your settings. Press the Action Menu button and select Calibrate.Ĭalibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Submit a valid PIN to update the settings for this beacon. (If the RadBeacon is not configurable, then an "unable to connect" message will be displayed after approximately 15 seconds.) The settings displayed include: If the RadBeacon is configurable, its detailed settings will be displayed. Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by pressing the SCAN button. Once discovered, if the beacon is configurable, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby Radius Networks beacons. The RadBeacon app from Radius Networks requires an Android device running Android 4.3 or higher and equipped with Bluetooth 4.0 capabilities. The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services and the AltBeacon proximity services for Android devices.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |